If a CmDongle is connected and can be displayed and read in CodeMeter Control Center, it can usually be assumed that it is working. A defect of a CmDongle is already apparent when connecting. In CodeM more
Which mode is to be used can be set via the Windows registry and the UseUmsDA key. Proceed as follows to open the registry: - Press the key combination [Windows] + [R] to open the dialog "Execute". - more
In such a case, it may help to give CodeMeter full disk access. To do this, please proceed as follows: 1. Open System Preferences. 2. Navigate to System Preferences Security & Privacy more
EBL stands for "ExecuteBciLow". And Bci for "Basic Command Interface". Here corresponding commands are sent to the CmDongle and then evaluated or processed there. Accordingly, errors can also occur, w more
If the CmDongle is not recognized as a device by Linux-Embedded, the CmDongle must be mounted with increased rights. For HID-Dongles (Human Interface Device) enter the command: sudo chmod o+rw /dev/hi more
If those errors display, errors in the USB communication with the CmDongle have been occurred. If the communication after several attempts still fails, finally Error 70 displays and no further communi more
The flashing represents mainly an information for our hardware department to gain further information in special cases. As a rule, the LED of the CmDongle flashes during read or write accesses and can more
In earlier firmware versions it could happen that the certificates within a Firm Item were no longer correctly available due to a very rare error. In this case, no Context File of this Firm Item could more
You can reset the CodeMeter password for your CmDongle using the CodeMeter Master Password of this CmDongle. Please proceed as follows: - Open CodeMeter Control Center. - Select the desired CmDongle o more
Depending on the type, CmDongles support different communication types (USB device classes): Human Interface Device (HID) and Mass Storage Device (MSD). In the case of HID, a connected CmDongle behave more
To run the CmStick BMC under current Debian-based / Red Hat Enterprise Linux distributions, the CodeMeterLin Deamon must be started as 'root'. Proceed as follows: 1. Execute the following command in t more
Starting with Version 5.0, CodeMeter supports devices that conform to the USB Human Interface Device (HID) class specification. As an alternative option to the Mass Storage Device status, CmDongles ca more
For older CmDongles with a specific controller version, there is no firmware version 2.x, because these controllers do not possess sufficient memory for the changed firmware update procedure that was more
Depending on the BIOS and the configuration of the boot manager of your system, it might occur that your system hangs during boot procedure. This happens because the system tries to boot from the CmDo more
There may be several reasons for this: - By default, all CmDongles 3-xxx (without flash memory) are delivered with HID configuration. Thus the CmDongle is detected as a potential keyboard or mouse dev more
Please send an e-mail to support(at)wibu.com. If you have a license request file (*.WibuRaC) you previously created via CodeMeter Control Center, attach it to the mail. Alternatively, you can also att more
There are two ways to perform an online firmware update. Either you use CodeMeter Control Center or the CodeMeter command line utility cmu. CodeMeter Control Center - Open CodeMeter Control Center. - more
To update the firmware of a CmDongle that is connected to a system without internet access, it is possible to update it with an offline firmware update. You can find the required update files on our w more
To check, if the if CodeMeter WebAdmin is running on your Linux system, please proceed as follows: 1. Open a terminal window. 2. Type command: sudo service codemeter-webadmin status The deamon script more
CodeMeter WebAdmin is based on HTML code including Javascript. The full functionality requires the activation of Javascript, e.g. on selecting a single CmContainer when several CmContainer are used. W more
Questa schermata riduce il consumo di energia del monitor quando non sei attivo sul nostro sito. Per riprendere la navigazione è sufficiente muovere il mouse.